Daewoo Matiz since 1997 of release
1. The general data
2. Maintenance service
3. The engine
4. Transmission
5. A running gear
6. A steering
7. Brake system
8. Systems of heating, ventilation and air-conditioning
9. A body electric equipment
10. A body
10.1. An interior
10.2. Seats
10.3. Glasses and mirrors
10.4. Elements of external furnish of a body
10.5. Bumpers
10.6. Doors
10.6.1. The design description
10.6.2. Removal and installation of doors and their elements
10.6.3. Adjustment of a clamp of the lock of a door
10.6.4. Adjustment of a clamp of the lock of a door of a luggage carrier
10.7. A roof
10.8. Seat belts
10.9. A forward part of a body
10.10. A back part of a body
10.11. A frame and a body skeleton
10.12. Restoration of tightness and elimination of scratches of a body
11. Schemes электроборудования
 




Soap2 day





10-6-2-snyatie-i-ustanovka-dverejj-i-ikh-ehlementov.html

10.6.2. Removal and installation of doors and their elements

Forward door in gathering
Removal
Removal and installation of a forward door spend with the assistant.
Disconnect a wire of "weight" from the storage battery.
Disconnect an electric socket under the control panel. In case of a detachment of an electric socket from outside the forward passenger remove перчаточный a box.
Remove a forward wing.
Remove a forward door in gathering in a following order:
- Open a door, support its supports or jacks, having laid between them and a door pure rags;

Fig. 10.65. Removal of a forward door: 1 — bolts of fastening of a loop of a door; 2 — the terminator of opening of a forward door; 3 — a forward door 4 — a rubber sealant




- Turn away bolts 1 (fig. 10.65) fastenings of a loop of a door;
- Turn away a bolt of 2 fastenings of the terminator of opening of a door;
- Remove a rubber sealant 4 between a body and a door;
- Remove a forward door in gathering 3.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Establish a rubber sealant between a body and a door.
Establish a forward door and fix bolts, without tightening them it is definitive.
Adjust door position.
Definitively tighten bolts of fastening of a loop of a door to a body.
Establish the terminator of opening of a door and fix a bolt.
Establish a wing.
Connect an electric socket.
Connect "a weight" wire to the storage battery.
Execute check on absence of leak of water.
Check up on absence of noise of a wind.
Back door in gathering
Removal
Removal and installation of a back door spend with the assistant.
Disconnect a wire of "weight" from the storage battery.
Examine the bottom panel of an upholstery of an average rack.

Fig. 10.66. An arrangement of an electric socket (1) back doors




Disconnect an electric socket 1 (fig. 10.66) a back door.
Remove a back door in gathering in a following order:
- Open a back door, support its supports or jacks, having laid between them and a door pure rags;

Fig. 10.67. An arrangement of bolts of fastening of a loop of a door (1) and the terminator (3) opening of a back door (4) and a rubber sealant (2)




- Turn away bolts 1 (fig. 10.67) fastenings of a loop of a door to a body;
- Turn away a bolt of 3 fastenings of the terminator of opening of a door;
- Remove a rubber sealant 2 between a body and a door;
- Remove a forward door in gathering 4.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Establish a rubber sealant between a body and a door.
Establish a back door and fix bolts, without tightening them it is definitive.
Adjust door position.
Definitively tighten bolts of fastening of a loop of a door to a body.
Establish the terminator of opening of a door and fix a bolt.
Connect an electric socket.
Connect "a weight" wire to the storage battery.
Whether check up provides a sealant from a water leaking.
Luggage carrier door in gathering
Removal
Removal and installation of a door of a luggage carrier is necessary for spending with the assistant.
Disconnect a wire of "weight" from the storage battery.
Remove the panel of an upholstery of a niche for a spare wheel in a luggage compartment.

Fig. 10.68. A detachment of electric sockets (1) doors of a luggage carrier




Disconnect electric sockets 1 (fig. 10.68) luggage carrier doors.
Remove a rack of a door of a luggage carrier.
Remove a luggage carrier door in a following order:

Fig. 10.69. A reversing of bolts of fastening of a loop of a door of a luggage carrier




- Turn out bolts of fastening of a loop of a door of a luggage carrier (fig. 10.69);
- Remove a rubber sealant between a body and a luggage carrier door;
- Remove a luggage carrier door.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Establish a door of a luggage carrier and fix bolts, without tightening them it is definitive.
Adjust position of a door of a luggage carrier.
Definitively tighten bolts of fastening of a loop of a door of a luggage carrier.
Establish a rack of a door of a luggage carrier.
Connect an electric socket of a door of a luggage carrier.
Establish the panel of an upholstery of a niche for a spare wheel in a luggage compartment.
Connect "a weight" wire to the storage battery.
Directing glasses of a forward door
Removal
Remove the panel of an upholstery from a forward door.
Remove an upholstery from a forward door.
Remove an external rear-view mirror from a forward door.
Remove directing рейку from a door in a following order:

Fig. 10.70. Removal directing рейки: 1 — screws; 2 — internal bolts; 3 — external bolts; 4 — glass of a forward door




- Turn out screws 1 (fig. 10.70);
- Turn out internal bolts 2;
- Turn out external bolts 3;
- Remove directing рейку a forward door 4.

Fig. 10.71. Removal directing glasses (1) from a forward door




Remove directing glasses 1 (fig. 10.71) from a forward door.
Installation
Establish directing glasses.
Establish directing рейку and fix bolts and the screw.
Establish an external rear-view mirror.
Establish an upholstery of a forward door.
Establish the panel of an upholstery of a forward door.
Directing glasses of a back door
Removal
Remove an internal sealant from a door.
Remove an external sealant from back doors.
Remove the panel of an upholstery of a back door.

Fig. 10.72. Removal of an upholstery of a back door: 1 — an upholstery; 2 — an arm of the handle of a door




Remove an upholstery 1 (fig. 10.72) a back door.
Turn out the screw and remove an arm of 2 handles of a door. In case of a car complete set делюкс remove an upholstery after removal of an arm of the handle of a door.

Fig. 10.73. An arrangement of the screw (1) fastenings of a directing element (2)




Turn out screws 1 (fig. 10.73) and remove directing element 2.
Remove top directing рейку and directing glasses in a following order:

Fig. 10.74. Removal top directing рейки and directing glasses: 1 — bolts; 2 — directing рейка and directing glasses




- Turn out bolts 1 (fig. 10.74);
- Lift and simultaneously remove top directing рейку and directing glasses 2.
Installation
Establish top directing рейку and directing glasses of a back door.
Establish directing element and fix screws.
Establish an upholstery of a back door.
Establish the panel of an upholstery of a back door.
Establish an external sealant on a back door.
Establish an internal sealant on a back door.
Clamp of the lock of a door
Removal

Fig. 10.75. An arrangement of screws (1) fastenings of a clamp (2) locks of a back door




Turn out screws 1 (fig. 10.75) and remove a clamp 2 locks of a back door.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Establish a clamp of the lock of a back door and fix screws.
Clamp of the lock of a door of a luggage carrier
Removal
Open a door of a luggage carrier and fix it.
Remove a clamp of the lock of a door of a luggage carrier in a following order:

Fig. 10.76. Removal of a clamp of the lock of a door of a luggage carrier: 1 — screws; 2 — a cable; 3 — a clamp of the lock of a door of a luggage carrier




- Turn away screws 1 (fig. 10.76);
- Disconnect a cable 2;
- Remove a clamp 3.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Connect a cable.
Establish a clamp of the lock of a door of a luggage carrier and fix screws.
The lock of a forward door
Removal
If the car is equipped by system of the central lock, disconnect a wire of "weight" from the storage battery.
Remove the panel of an upholstery of a forward door.
Remove an upholstery from a forward door.
Disconnect draught of the external handle of a door from the door lock.

Fig. 10.77. An arrangement of screws (1) fastenings of the lock (2) forward doors




Turn out screws 1 (fig. 10.77) and remove the lock 2 forward doors. If the car is equipped by system of the central lock, disconnect a socket of the electric drive of the lock.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Will put the lock of a door and fix screws. If the car is equipped by system of the central lock, connect an electric drive socket.
Connect draught of the external handle and draught from the lock cylinder to the door lock.
Establish an upholstery on a forward door.
Establish the panel of an upholstery of a forward door.
Connect "a weight" wire to the storage battery.
The lock of a back door
Removal
If the car is equipped by system of the central lock, disconnect a wire of "weight" from the storage battery.
Remove the panel of an upholstery of a door.
Remove an upholstery 1 (fig. 10.72 see) back door. In case of a car complete set делюкс remove an upholstery after removal of an arm of the handle of a door.
Turn out screws 1 (fig. 10.73 see) and remove directing element 2.

Fig. 10.78. A place of a detachment of draught (1) external handles from the door lock




Disconnect draught 1 (fig. 10.78) the external handle from the door lock.

Fig. 10.79. An arrangement of screws (1) fastenings of the lock (2) back doors




Turn out screws 1 (fig. 10.79) and remove the lock 2 back doors. If the car is equipped by system of the central lock, disconnect a socket of the electric drive of the lock.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Will put the lock of a back door and fix screws. If the car is equipped by system of the central lock, connect an electric drive socket.
Connect draught of the external handle of a door for the door lock.
Establish directing рейку and fix screws.
Establish an upholstery on a door.
Establish the panel of an upholstery of a door.
Connect "a weight" wire to the storage battery.
The electric drive of the lock of a door
Removal
Disconnect a wire of "weight" from the storage battery.
Remove the panel of an upholstery of a door.
Remove an upholstery from a door.
Remove the door lock in gathering.

Fig. 10.80. An arrangement of screws (1) fastenings of the electric drive (2) locks of a door




Turn out screws 1 (fig. 10.80) and remove the electric drive 2 locks of a door.
Installation
Will put the electric drive the door lock in gathering and fix screws.
Will put the door lock in gathering on the car.
Establish an upholstery on a door.
Establish the panel of an upholstery of a door.
Connect "a weight" wire to the storage battery.
The lock of a door of a luggage carrier
Removal
Disconnect a wire of "weight" from the storage battery.
Remove the panel of an upholstery of a door.
Remove пылевлагозащитную a film of a door of a luggage carrier.

Fig. 10.81. A place of a detachment of draught (1) locks from the cylinder of the lock of a door of a luggage carrier




Remove draught 1 (fig. 10.81) the lock from the cylinder of the lock of a door of a luggage carrier.

Fig. 10.82. An arrangement of screws (1) fastenings of the lock (2) doors of a luggage carrier




Turn out screws 1 (fig. 10.82) and remove the lock of 2 doors of a luggage carrier.
Installation
Will put the lock of a door of a luggage carrier and fix screws.
Establish draught of the lock for the cylinder of the lock of a door of a luggage carrier.
Establish an upholstery of a door of a luggage carrier.
Establish the panel of an upholstery of a door.
Connect "a weight" wire to the storage battery.
The internal and external handle of a forward door
Removal
Disconnect a wire of "weight" from the storage battery.

Fig. 10.83. An arrangement of the screw (1) fastenings of the internal handle (2) forward doors




Turn out the screw 1 (fig. 10.83) and remove the internal handle 2 forward doors.
Remove draughts of the lock of a forward door.

Fig. 10.84. A reversing of bolts (1) fastenings of the external handle (2) forward doors




Turn out bolts 1 (fig. 10.84) and remove the external handle 2 forward doors.
Installation
Establish the external handle of a forward door and fix bolts.
Establish draughts of the lock of a forward door.
Establish the internal handle of a door and fix screws.
Connect "a weight" wire to the storage battery.
The external handle of a back door
Removal
Disconnect a wire of "weight" from the storage battery.
Remove the door lock.

Fig. 10.85. A reversing of bolts (1) fastenings of the external handle (2) back doors




Turn out bolts 1 (fig. 10.85) and remove the external handle 2 back doors.
Installation
Establish the external handle of a back door and fix bolts.
Will put the lock of a back door.
Connect "a weight" wire to the storage battery.
The cylinder of the lock of a door
Removal
Disconnect a wire of "weight" from the storage battery.
Remove the external handle of a door.
Remove the cylinder of the lock of a door from the external handle of a door in a following order:

Fig. 10.86. Removal of a clip (1) fastenings of the cylinder (2) locks of a door




- Remove a clip 1 (fig. 10.86);
- Remove the cylinder 2 locks of a door.
Installation
Establish the cylinder of the lock of a door and fix a clip.
Establish the external handle of a door.
Connect "a weight" wire to the storage battery.
The cylinder of the lock of a door of a luggage carrier
Removal
Disconnect a wire of "weight" from the storage battery.
Open a luggage carrier door.
Remove the engine of a back screen wiper in gathering.
Remove the cylinder of the lock of a door of a luggage carrier in a following order:

Fig. 10.87. Removal of the cylinder of the lock of a door of a luggage carrier: 1 — draught of the lock of a luggage carrier; 2 — nuts of fastening of the cylinder of the lock of a door; 3 — the cylinder of the lock of a door of a luggage carrier




- Disconnect draught 1 (fig. 10.87) the lock of a door of a luggage carrier;
- Turn away a nut 2 from the cylinder of the lock of a door of a luggage carrier;
- Remove the cylinder of the lock of 3 doors of a luggage carrier.
Installation
Establish the cylinder of the lock of a door of a luggage carrier.
Establish the engine of a back screen wiper in gathering.
Connect "a weight" wire to the storage battery.
Mechanical стеклоподъемник
Removal
Remove glass from a forward door.
Remove стеклоподъемник in a following order:

Fig. 10.88. An arrangement of bolts (1) fastenings mechanical стеклоподъемника (2) forward doors




- Turn out bolts 1 (fig. 10.88) fastenings стеклоподъемника;
- Through apertures at doors, remove стеклоподъемник 2.
Installation
Establish стеклоподъемник and fix bolts.
Establish glass.
Electric стеклоподъемник
Removal
Disconnect a wire of "weight" from the storage battery.
Remove glass.
Remove electric стеклоподъемник in gathering in a following order:

Fig. 10.89. Fastening of the electrolift of a forward door: 1 — an electric socket; 2 — bolts; 3 — the electrolift of a forward door




- Disconnect an electric socket 1 (fig. 10.89) the engine стеклоподъемника;
- Turn out bolts of 2 fastenings стеклоподъемника;
- Through apertures at doors, remove стеклоподъемник 3.

Fig. 10.90. Engine fastening стеклоподъемника to стеклоподъемнику: 1 — fastening screws; 2 — стеклоподъемник




Turn out screws 1 (fig. 10.90) and remove the engine стеклоподъемника with стеклоподъемника 2. At engine removal стеклоподъемника be cautious, as it is possible to be wounded easily.
Installation
Establish the engine стеклоподъемника on стеклоподъемник and fix screws.
Establish стеклоподъемник in gathering and fix screws.
Connect an electric socket of the engine стеклоподъемника.
Establish glass.
Connect "a weight" wire to the storage battery.
Door loop
Removal
Removal and installation of a loop of a door spend with the assistant.
Open a door and support its supports or jacks, having laid between them and a door pure rags.

Fig. 10.91. Removal of a loop of a door: 1 — a bolt of fastening of a loop to a body; 2 — a bolt of fastening of a loop 3 to a door




Turn away bolts 1 (fig. 10.91) fastenings of a loop of a door to a body.
Turn away bolts of 2 fastenings of a loop of a door to a door and remove a loop 3.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Establish a loop on a door and a body and fix bolts.
The terminator of opening of a door
Removal
Remove a door upholstery.
Remove the terminator of opening of a door in a following order:

Fig. 10.92. Removal of the terminator of opening of a door: 1 — a bolt of fastening of the terminator to a body; 2 — a bolt of fastening of the terminator to a door; 3 — the terminator




- Turn out a bolt 1 (fig. 10.92) terminator fastenings to a body;
- Turn out bolts of 2 fastenings of the terminator to a door;
- Remove the terminator of opening of a door 3.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Establish the terminator of opening of a door on a door and a body and fix bolts.
Establish a door upholstery.
Internal sealant (делюкс)
Removal
Remove the panel of an upholstery of a door.
Remove an internal sealant from the panel of an upholstery of a door in a following order:

Fig. 10.93. Removal of an internal sealant: 1 — pulling together eyelets; 2 — a sealant




- Straighten pulling together eyelets 1 (fig. 10.93);
- Remove a sealant 2.
Installation
Establish a sealant on the panel of an upholstery of a door.
Bend pulling together eyelets for sealant fastening on the panel of an upholstery of a door.
Establish the panel of an upholstery of a door.
Door sealant
Removal

Fig. 10.94. An arrangement of a bolt of fastening of the terminator of opening of a door




Turn out a bolt of fastening of the terminator of opening of a door (fig. 10.94).
Remove a door sealant in a following order:

Fig. 10.95. Removal of a sealant of a door: 1 — a clip; 2 — sealant clamps




- Remove a clip 1 (fig. 10.95);
- Remove clamps of 2 sealants;
- Remove a door sealant.
Installation
Establish a sealant of a door and fix clips and clamps.
Screw a bolt of fastening of the terminator of opening of a door.
Door upholstery
Removal
Remove the panel of an upholstery of a door.
Remove an upholstery 1 (fig. 10.72 see) doors. At a car complete set делюкс remove an upholstery after removal of an arm of the handle of a door.
Installation
Establish an upholstery of a back door.
Establish an arm of the handle of a door.
Establish the panel of an upholstery of a back door.
Extreme sealant of a door
Removal
Put a combination label on an extreme sealant of a door the erased handle.
Remove an extreme sealant of a door in a following order:

Fig. 10.96. Removal of an extreme sealant of a door: 1 — the panel of an upholstery of a threshold; 2 — the panel of an upholstery of an average rack; 3 — an extreme sealant of a door




- Partially remove the panel 1 (fig. 10.96) threshold upholsteries;
- Partially remove the bottom panel of 2 upholsteries of an average rack;
- Remove an extreme sealant of a door 3.
Installation
Establish an extreme sealant according to earlier put label.
Establish the panel of an upholstery of a threshold and the bottom panel of an upholstery of an average rack.
Rack of a door of a luggage carrier
Removal
Open a door of a luggage carrier and fix it in this position.
Remove a rack of a door of a luggage carrier in gathering in a following order:

Fig. 10.97. Removal of a rack of a door of a luggage carrier: 1 — a nut of a spherical connector on a rack of a back part of a body; 2 — a nut of a spherical connector on a luggage carrier door




- Turn away a nut of a spherical connector 1 (fig. 10.97) racks from a back part of a body;
- Turn away a nut of a spherical connector of a rack 2 from a luggage carrier door;
- Remove a rack of a door of a luggage carrier.
Installation
Establish a rack of a door of a luggage carrier and screw nuts of spherical connectors of a rack.



To return back
10.6.1. The design description
On the following page
10.6.3. Adjustment of a clamp of the lock of a door