Daewoo Matiz since 1997 of release
1. The general data
2. Maintenance service
3. The engine
4. Transmission
5. A running gear
6. A steering
7. Brake system
8. Systems of heating, ventilation and air-conditioning
9. A body electric equipment
10. A body
10.1. An interior
10.2. Seats
10.3. Glasses and mirrors
10.4. Elements of external furnish of a body
10.5. Bumpers
10.6. Doors
10.7. A roof
10.8. Seat belts
10.8.1. The design description
10.8.2. Removal and installation of seat belts
10.9. A forward part of a body
10.10. A back part of a body
10.11. A frame and a body skeleton
10.12. Restoration of tightness and elimination of scratches of a body
11. Schemes электроборудования
 









10-8-1-opisanie-konstrukcii.html

10.8.1. The design description

Control lamp of a seat belt of the driver
The seat belt of the driver is connected to a control lamp in the panel of devices for a reminder to the driver about not fastened belt at ignition inclusion.
Three-dot seat belt with blocking натяжителем
The seat belt with three-dot fastening and blocking натяжителем limits moving of the driver and is better protects in case of failure.
Three-dot seat belt with emergency blocking натяжителем
The seat belt of forward sitting with three-dot fastening with emergency blocked натяжителем (АБН) always is unblocked, providing the passenger moving freedom, excepting sudden delay, sudden acceleration or sudden turn in the course of car maneuvering.
Seat belt of back sitting
For the passengers sitting with edge of back sitting, there is a seat belt with three-dot fastening with emergency blocked натяжителем. The Seat belt is always unblocked, giving to the passenger moving freedom, excepting sudden delay, sudden acceleration and at sudden turn in the course of car maneuvering.
Zone seat belt of back sitting with point-to-point fastening
The zone seat belt of back sitting with point-to-point fastening for the passenger sitting on the centre, is one continuous tape passing from an anchor through a uvula and a buckle of a seat belt in single натяжителя.
Check of functional work

Preventions
Store sharp subjects and potentially damaging elements far away from seat belts. Avoid bends and damage of any part of a buckle or a latch uvula.
Do not bleach and do not paint over a seat belt tape. Use only soft soap and water at cleaning of belts.
At installation of bolts and anchor screws at first turn their hands for prevention of damage of a carving.
Do not try to repair the mechanism or a casing натяжителя. Replace all faulty parts in gathering on similar in gathering.


Replace belts with cuts and damages.
Check up all bolts of an anchor of a seat belt to be convinced of their reliability.
Check up buckles of seat belts. The buckle should be blocked and unblocked easily.
After introduction of a uvula in a buckle sharply pull a belt. The buckle should remain blocked.
Completely extend a humeral part of a belt to be convinced of absence of wave formations or deterioration of a belt.
Allow a humeral part of a belt to be involved completely. The belt should be involved freely.

Fig. 10.105. Seat belts: 1 — a seat belt of forward sitting; 2 — a buckle of a seat belt of forward sitting; 3 — a seat belt of back sitting (with three-dot fastening); 4 — a seat belt of back sitting (for point-to-point fastening) / a buckle for three-dot fastening); 5 — a buckle of a seat belt of back sitting (for three-dot fastening/for of point-to-point fastening)




Seat belts are shown on fig. 10.105.
The moments of an inhaling of bolts of fastening of seat belts are resulted in tab. 10.2.

Table 10.2 the     Moments of an inhaling of bolts of fastening of seat belts
The top bolt of fastening of a seat belt
30-45
The bottom bolt of fastening of a seat belt
30-45
Fastening bolt натяжителя a seat belt
30-45
Bolt of fastening of a buckle of a seat belt
30-45
Bolt of fastening of a buckle of a seat belt of back sitting
30-45

To return back
10.8. Seat belts
On the following page
10.8.2. Removal and installation of seat belts