Daewoo Matiz since 1997 of release
1. The general data
2. Maintenance service
3. The engine
4. Transmission
5. A running gear
6. A steering
7. Brake system
8. Systems of heating, ventilation and air-conditioning
9. A body electric equipment
10. A body
10.1. An interior
10.2. Seats
10.3. Glasses and mirrors
10.4. Elements of external furnish of a body
10.5. Bumpers
10.6. Doors
10.7. A roof
10.8. Seat belts
10.9. A forward part of a body
10.9.1. The design description
10.9.2. Removal and installation of elements of a forward part of a body
10.10. A back part of a body
10.11. A frame and a body skeleton
10.12. Restoration of tightness and elimination of scratches of a body
11. Schemes электроборудования
 









10-9-2-snyatie-i-ustanovka-ehlementov-perednejj-chasti-kuzova.html

10.9.2. Removal and installation of elements of a forward part of a body

Sealant of a forward part
All places, whence can occur water leaks, are condensed in the course of manufacture by strong quality sealants. If consolidation of a separate site is necessary, use a sealant with high quality and average density which will keep the plastic characteristics while in service and can be if necessary painted.
Ventilating lattice
Removal
Remove the screen wiper lever in gathering.
Turn out screws and remove a ventilating lattice in a following order:

Fig. 10.114. Removal of a ventilating lattice: 1 — screws; 2 — plastic clips; 3 — a ventilating lattice




- Remove заглушки and turn out screws 1 (fig. 10.114);
- Remove the bottom fixing plastic clips 2;
- Close a cowl;
- Lift a ventilating lattice 3;
- Disconnect a socket of a forward hose of a washer;
- Remove a ventilating lattice.
Installation
Connect a socket of a forward hose of a washer.
Establish a ventilating lattice and fix clips and screws.
Establish the screen wiper lever in gathering.
Cowl
Removal
Open a cowl and enclose pure rags under its corners to protect a paint and varnish covering of the car at cowl removal.
Using a marker, note position of hinges on a cowl.

Fig. 10.115. An arrangement of bolts (1) fastenings of hinges of a cowl (2)




Ask the assistant to support a cowl in open position, turn out bolts 1 (fig. 10.115) fastenings of the left and right hinges of a cowl 2, being careful, remove a cowl.
Check up a condition of hinges of a cowl on presence люфта and deterioration, if necessary replace them.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

With two assistants establish a cowl and screw in by hand bolts of fastening of hinges of a cowl. Level cowl hinges according to earlier made labels, tighten bolts of fastening of a cowl.
Cowl loop
Removal
Remove a cowl.

Fig. 10.116. Removal of a loop of a cowl: 1 — screws with заглушками; 2 — screws; 3 — a ventilating lattice




Remove заглушки and turn out screws 1 (fig. 10.116).
Turn out screws 2 and remove a ventilating lattice 3.

Fig. 10.117. An arrangement of bolts (1) fastenings of the top part of a forward wing




Turn out bolts 1 (fig. 10.117) fastenings of the top part of a wing.

Fig. 10.118. An arrangement of bolts (1) fastenings of a loop (2) cowls




Turn out bolts 1 (fig. 10.118) and remove a loop 2 cowls.
Installation

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Establish a loop of a cowl and fix bolts.
Screw bolts along the top part of a wing.
Establish a ventilating lattice and fix clips and screws.
Establish a cowl.
The basic lever of a cowl
Removal
Open a cowl and fix it in open position.
Remove a support from a cowl in a following order:

Fig. 10.119. Removal of the basic lever of a cowl: 1 — pins; 2 — a cowl support




- Sharp gimlet press pins 1 (fig. 10.119);
- Remove a support of a cowl 2.

Fig. 10.120. Removal of the basic lever of a cowl (1) from a cowl support




Remove the basic lever of a cowl 1 (fig. 10.120) from a cowl support.
Installation
Establish the basic lever of a cowl on a cowl support.
Establish a cowl support on a cowl and fix pins.
Cowl latch
Removal
Open a cowl.
Remove a cowl latch to a following order:

Fig. 10.121. Removal of a latch of a cowl: 1 — screws; 2 — a cowl latch; 3 — a cable of opening of the lock of a cowl




- Turn out screws 1 (fig. 10.121);
- Disconnect a cable of 3 opening of the lock of a cowl;
- Remove a latch of a cowl 2.
Installation
Connect a cable of opening of the lock of a cowl to a latch.

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Establish a latch of a cowl and fix screws.
Close a cowl.
The lever of opening of a latch of a cowl
Removal

Fig. 10.122. An arrangement of a nut (1) cables of opening of a latch of a cowl




Turn away a nut 1 (fig. 10.122) a cable of opening of a latch of a cowl in the control panel.

Fig. 10.123. A detachment of a cable (1) from the lever (2) opening of a latch of a cowl




Disconnect a cable 1 (fig. 10.123) and remove the lever of 2 opening of a latch of a cowl.
Installation
Connect a cable of opening of a latch of a cowl to the lever of a latch of a cowl.

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Establish the lever of opening of a latch of a cowl in the control panel and screw a nut of a latch of a cowl.
Cable of opening of a latch of a cowl
Removal
Remove a cable of opening of a latch of a cowl from the control panel.

Fig. 10.124. Removal of a cable (1) opening of a latch of a cowl




Move a cable 1 (fig. 10.124) in an arrow direction to a motor compartment through an aperture in a body.
Open a cowl and fix it in open position.
Disconnect a cable of opening of a latch of a cowl from a cowl latch.
Remove a plastic strip and remove a cable of opening of a latch of a cowl.
Installation
Connect a cable of opening of a latch of a cowl to a cowl latch.
Prepare a cable of opening of a latch of a cowl with a plastic strip.
Press a cable in a direction to a motor compartment through an aperture in a body.
Connect a cable of opening of a latch of a cowl to the lever of opening of a latch of a cowl.
Wing
Removal
Disconnect a wire of "weight" from the storage battery.
Lift the car and establish on support.
Remove forward wheels.

Fig. 10.125. An arrangement of screws (1) fastenings грязезащитных guards (2) arches of forward wheels




Turn out screws 1 (fig. 10.125), release clamps and remove грязезащитные guards of 2 arches of forward wheels.

Fig. 10.126. An arrangement of bolts (1) fastenings of the bottom part of a forward wing and bolts (2) fastenings to a forward rack




Turn out a bolt 1 (fig. 10.126) fastenings of the bottom part of a forward wing and a bolt of 2 fastenings to a forward rack.
Open a forward door and turn out a bolt of 2 fastenings of a wing to a forward rack.

Fig. 10.127. An arrangement of bolts (1) fastenings of a forward wing to facing of a bumper and a forward bolt (2) fastenings of a wing




Turn out bolts 1 (fig. 10.127) fastenings of a forward wing to bumper facing.
Turn out a forward bolt of 2 fastenings of a wing.
Lower the car.
Remove a ventilating lattice.

Fig. 10.128. An arrangement of a bolt (1) fastenings of a back top part of a wing




Turn out a bolt 1 (fig. 10.128) fastenings of a back top part of a wing.
Remove facing of a forward bumper.

Fig. 10.129. An arrangement of a bolt (1) fastenings of a forward part of a wing




Turn out a bolt 1 (fig. 10.129) fastenings of a forward part of a wing.
Turn out bolts along the top part of a wing.
Remove a wing.
Installation
Establish a wing.

The note
Contact of surfaces from different metals can lead to fast corrosion. Be convinced of application of appropriate inhalings in order to avoid premature corrosion.

Screw bolts along the top part of a wing.
Establish facing of a forward bumper.
Establish a ventilating lattice.
Lift and fix the car.
Screw bolts under a wing.
Screw screws of fastening of a forward wing to bumper facing.
Open a forward door and screw a bolt of fastening of a wing to a forward rack.
Screw a bolt of fastening of the bottom part of a wing.
Establish грязезащитные guards of arches of forward wheels and fix their screws and clamps.
Establish forward wheels.
Lower the car.
Connect "a weight" wire to the storage battery.



To return back
10.9.1. The design description
On the following page
10.10. A back part of a body