Daewoo Matiz since 1997 of release
1. The general data
2. Maintenance service
2.1. Maintenance service
2.2. Replacement of engine oil and the oil filter
2.3. Replacement of spark plugs
2.4. Check топливопроводов
2.4.1. Replacement of the fuel filter
2.4.2. Adjustment of a thermal backlash of valves
2.5. Check and adjustment of a corner of an advancing of ignition
2.6. Check of system of cooling on absence of leaks
2.7. Check of level of oil in a transmission
2.8. Check of the spherical hinge of a forward suspension bracket
2.9. Check axial люфта a back wheel
2.10. Prorolling of system of the hydraulic booster of a steering
2.11. Removal of air from brake system
2.12. Anticorrosive materials
3. The engine
4. Transmission
5. A running gear
6. A steering
7. Brake system
8. Systems of heating, ventilation and air-conditioning
9. A body electric equipment
10. A body
11. Schemes электроборудования
 









2-4-2-regulirovka-teplovogo-zazora-klapanov.html

2.4.2. Adjustment of a thermal backlash of valves

Check up and adjust a backlash of valves in a following order:
- Remove the case of the air filter and the resonator;
- Turn out шестигранные bolts of fastening of a cover of a head of the block and uncover;

Fig. 2.9. Installation of the piston of the first cylinder in ВМТ in a compression step




- Turn a cranked shaft before installation of the piston of the first cylinder in the top dead point (ВМТ) in a compression step. In this position the label "and" (fig. 2.9) on a camshaft pulley should be combined with the triangular index b on a back casing of a gear belt, and the label "with" on a pulley of a cranked shaft to be combined with the index d on the case of the oil pump;

Fig. 2.11. A place of measurement of a thermal backlash a valves




- Check up a thermal backlash of valves and (fig. 2.11) in position of the piston of the first cylinder in ВМТ in a step of compression of inlet valves of 1 and 2 cylinders and final valves of 1 and 3 cylinders;

Fig. 2.10. Installation of the piston of the first cylinder in ВМТ in a release step




- Turn a cranked shaft on 360 (1 turn), thus the piston of the first cylinder will be established in position ВМТ of the first cylinder in a release step, and the label "and" (fig. 2.10) on a camshaft pulley should be combined with the index b on a back casing of a gear belt;
- In this position check up a thermal backlash and (fig. 2.11) valves of the inlet valve 3 cylinders and the final valve 2 cylinders;

Fig. 2.12. Use щупа (1) for measurement of a thermal backlash of valves




- Check of a thermal backlash of valves spend щупом (fig. 2.12).
The measured size of a thermal backlash should correspond specified in Specifications, otherwise it is necessary to adjust a thermal backlash.

Fig. 2.13. An arrangement of a counternut (1) and the adjusting screw (2) for adjustment of a thermal backlash of valves




At adjustment of a thermal backlash ослабьте a counternut 1 (fig. 2.13) and then tighten or ослабьте the adjusting screw 2 in appropriate way.

The note
In case of measurement of a thermal backlash at the hot engine warm up the engine until the electric fan of a radiator will start to work, then switch off the engine and 20—30 mines later measure a thermal backlash.




To return back
2.4.1. Replacement of the fuel filter
On the following page
2.5. Check and adjustment of a corner of an advancing of ignition