> Replacement of lobbies brake колодок. Daewoo Matiz (since 1997 of release)
Daewoo Matiz since 1997 of release
1. The general data
2. Maintenance service
3. The engine
4. Transmission
5. A running gear
6. A steering
7. Brake system
7.1. The design description
7.2. Diagnostics of brake system
7.3. Removal and installation of knots of brake system
7.4. Replacement brake колодок
7.4.1. Replacement of lobbies brake колодок
7.4.2. Replacement back brake колодок
7.5. Repair of knots of brake system
8. Systems of heating, ventilation and air-conditioning
9. A body electric equipment
10. A body
11. Schemes электроборудования
 




ƒилерские приборы в ”краине: t200 man дешевле только на Dilerscan.





7-4-1-zamena-perednikh-tormoznykh-kolodok.html

7.4.1. Replacement of lobbies brake колодок

Removal

Fig. 7.43. The forward disk brake mechanism: 1 — a support in gathering; 2 — a lobby brake колодка in gathering; 3 — a directing finger; 4 — a protective cover of a finger; 5 — lobbies brake колодки; 6 — a support; 7 — a spring clamping; 8 — a protective cover of the piston; 9 — the piston; 10 — a piston epiploon; 11 — the holder of a support with the cylinder; 12 — a dustproof cap; 13 — the union




The forward disk brake mechanism is shown on fig. 7.43.

Preventions
Necessarily replace all колодки on one axis of the car even if one is worn out only колодка. If brake колодки are established repeatedly, before removal it is necessary to mark them. At work brake колодок the brake dust containing asbestos, unhealthy is formed. Therefore at clearing brake колодок do not use compressed air and do not inhale a dust.
For clearing of brake mechanisms use only a special cleaner of brakes.


Uncover a tank of brake system.
Tighten a lay brake and block back wheels an emphasis.
Ослабьте nuts of fastening of a forward wheel. Lift a forward part of the car and establish on support. Remove a forward wheel.
Check up a brake disk on presence of cracks, especially round apertures under bolts of fastening of a wheel, and also on presence of deterioration or mechanical damages; if necessary replace both disks.

Fig. 7.44. An arrangement of the bottom bolt (1) fastenings of a support of a forward brake




Turn out the bottom bolt 1 (fig. 7.44) support fastenings. Thus the second key keep directing finger from проворачивания. Lift a support 1 (fig. 7.45) upwards, turning it round the top directing finger and a soft wire tie up to a forward rack. Do not turn on the top bolt of fastening of a support and a hollow bolt of fastening of a brake hose.

Fig. 7.45. A raising of a support (1) upwards, its turn round the top directing finger




Remove from the holder brake колодки.
If колодки are suitable to the further operation, clear their wire brush and rags.
Do not press a brake pedal at removed brake колодках.
Installation
Establish brake колодки on the holder of a support.
Establish a support into place and screw the bottom bolt of fastening of a support. If the support is not established on new колодки, a G-shaped clip, press the piston into a support. At вдвигании the piston the brake liquid is superseded from the brake cylinder in a broad tank. Therefore constantly observe of liquid level in a tank; if necessary pump out it from a tank.
Similarly replace brake колодки on the second forward wheel.
Establish wheels and lower the car on the earth.
Some times press a brake pedal that brake колодки have nestled on a brake disk.



ЂTo return back
7.4. Replacement brake колодок
On the following pageї
7.4.2. Replacement back brake колодок