Daewoo Matiz since 1997 of release
1. The general data
2. Maintenance service
3. The engine
4. Transmission
5. A running gear
6. A steering
6.1. System of the hydraulic booster of a wheel
6.2. The pump of the hydraulic booster of a wheel
6.3. The steering mechanism with the hydraulic booster
6.3.1. The design description
6.3.2. Possible malfunctions of the steering mechanism with the hydraulic booster and methods of their elimination
6.3.3. Repair of the steering mechanism
6.3.4. Removal and installation of a tip of steering draught
6.3.5. Removal and installation of a protective cover of steering draught
6.3.6. Removal and installation of a protective cover of a tip of steering draught
6.4. A steering column
7. Brake system
8. Systems of heating, ventilation and air-conditioning
9. A body electric equipment
10. A body
11. Schemes электроборудования
 









6-3-4-snyatie-i-ustanovka-nakonechnika-rulevojj-tyagi.html

6.3.4. Removal and installation of a tip of steering draught

Removal
Remove a wheel.
Disconnect a tip of steering draught from a rotary fist in a following order:

Fig. 6.40. An arrangement шплинта (1) and корончатой nuts (2) and use of a stripper of KM 507-in for branch of a tip of steering draught (3) from a rotary fist




- Remove шплинт 1 (fig. 6.40);
- Turn on корончатую a nut 2;
- Stripper of spherical hinges KM507-V separate a tip of steering draught 3 from a rotary fist.
Remove a tip of steering draught in a following order:

Fig. 6.41. Note mutual position of steering draught, a counternut of a tip of steering draught and a tip of steering draught (1)




- Note mutual position of steering draught, a counternut of a tip of steering draught and a tip of steering draught 1 (fig. 6.41);

Fig. 6.42. After easing of a counternut (1), turn out a tip of steering draught (2)




- Having turned counter-clockwise, ослабьте a counternut 1 (fig. 6.42) a tip of steering draught;
- Turn out a tip of steering draught 2.
Check
Check up a condition of spherical hinges of steering draught and a tip of steering draught.
Turn 10 times from an emphasis against the stop the spherical hinge of steering draught or a tip of steering draught.

Fig. 6.43. Use of spring scales for check of a twisting moment which is necessary for turn of steering draught or a finger of the spherical hinge




Spring scales check up a twisting moment necessary for turn of steering draught or a finger of the spherical hinge (fig. 6.43). The Twisting moment of the spherical hinge of steering draught and a tip of steering draught should be in limits 0,49—3,43 Нм. Otherwise replace steering draught and a tip of steering draught.
Installation
Screw a tip of steering draught on steering draught to earlier put label.
Connect a tip of steering bent for to a rotary fist.

Fig. 6.44. An arrangement and the moments of an inhaling of a counternut (1) and корончатой nuts (2) fastenings of a tip of steering draught




Tighten a counternut 1 (fig. 6.44) a tip of steering draught the moment 35—55 Нм.
Screw корончатую a nut of 2 fastenings of a tip of steering bent for to a rotary fist and tighten its moment 30—55 Нм.
Establish шплинт.
Establish a wheel.
Execute convergence adjustment, rotating an adjusting nut.



To return back
6.3.3. Repair of the steering mechanism
On the following page
6.3.5. Removal and installation of a protective cover of steering draught