3-3-10-remont-i-proverka-generatora-tipa-v-dac.html
3.3.10. Repair and check of the generator of type In (DAC)Dismantling
|
Fig. 3.132. The type generator In (DAC): 1 — the generator in gathering; 2 — the tension lever; 3 — a nut; 4 — a generator pulley; 5 — the plug; 6 — a generator cover; 7 — статор the generator; 8 — the bearing; 9 — fan blades; 10 — a generator anchor; 11 — the bearing; 12 — the case; 13 — a pressure regulator; 14 — щеткодержатель; 15 — диодный the bridge; 16 — a fixing plate; 17 — a coupling bolt; 18 — a back cover; 19 — a nut of fastening of the positive plug of the storage battery
|
Details of the generator of type In (DAC) are shown on fig. 3.132.
Remove the generator.
Remove a back cover of the generator in a following order:
|
Fig. 3.133. An arrangement of a nut (1) fastenings of the positive plug of the storage battery and a direction of removal of a back cover (2)
|
- Turn away a nut 1 ( fig. 3.133) fastenings of the positive plug of the storage battery;
- Remove a back cover 2.
Remove a pressure / regulator shchetkoderzhatel/diodnyj the bridge in gathering in a following order:
|
Fig. 3.134. An arrangement of lead connections (1) coils статора and диодного the bridge
|
- отпаяйте lead connections 1 ( fig. 3.134) coils статора and диодного the bridge;
|
Fig. 3.135. Removal of a regulator of pressure/shchetkoderzhatelja/diodnogo of the bridge in gathering: 1 — fastening screws диодного the bridge and a pressure regulator; 2 — the fastening screw диодного the bridge; 3 — the fastening screw shchetkoderzhatelja/a pressure regulator; 4 — the screw of fastening of a regulator of pressure; 5 — a regulator of pressure/shchetkoderzhatel/diodnyj the bridge in gathering
|
- Turn away bolts 1 ( fig. 3.135) fastenings диодного the bridge;
|
Fig. 3.136. Junctions диодного the bridge and щеткодержателя (1) and a regulator of pressure and щеткодержателя (2): and — диодный the bridge; b — a pressure regulator; with — щеткодержатель
|
- Turn away screws 1 ( fig. 3.136) fastenings диодного the bridge and a pressure regulator;
- Turn away the screw of 2 fastenings диодного the bridge;
- Turn away the screw of 3 fastenings of a shchetkoderzhatelja/regulator of pressure;
- Turn away the screw of 4 fastenings of a regulator of pressure;
- Remove a pressure / regulator shchetkoderzhatel/diodnyj the bridge in gathering 5.
Отпаяйте connection диодного the bridge and a regulator of pressure 1 ( fig. 3.136).
Отпаяйте connection of a regulator of pressure and щеткодержателя 2.
Visually check up диодный the bridge / a pressure / regulator щеткодержатель on absence of damages or breakage.
Remove a fixing plate before removal of a cover and the generator case in a following order:
|
Fig. 3.137. An arrangement of a fixing plate (1) and bolts (2) fastenings of the case of the generator (3) to a generator cover
|
- Turn away coupling bolts 2;
- Remove the case of the generator 3 from a generator cover.
Remove a pulley and a rotor in gathering from a generator cover in a following order:
|
Fig. 3.138. Removal of a pulley and a cover from a generator rotor: 1 — a fabric; 2 — a rotor; 3 — a nut; 4 — a pulley
|
- Fix a rotor in a vice, a pulley upwards 2;
- Turn away a nut of 3 fastenings of a pulley;
- Remove a pulley 4.
Uncover the generator and a rotor in a following order:
|
Fig. 3.139. Removal of the plug (1), a rotor (2) from a cover (4) generators and plugs (3)
|
- Remove a rotor 2 from a cover 4 generators;
- Remove the plug 3 from a rotor axis.
Check up the bearing in a generator cover on corrosion, deterioration, noise and other damages.
|
Fig. 3.140. Removal статора (2) from the case (1) generators
|
Check
|
Fig. 3.141. Check of a rotor (1) on chain breakage
|
Check up a rotor on chain breakage, using an ohmmeter. The indication should be low enough, or the rotor 1 should be replaced ( fig. 3.141).
|
Fig. 3.142. Check of the coil of a rotor on breakage of a chain (1) or short circuit (2)
|
Check up the rotor coil on breakage of a chain 1 ( fig. 3.142) or short circuit 2. Resistance of a winding should be 2,6—2,8 Ohm, or the rotor should be replaced. At check of short circuit the ohmmeter indication should be high enough, or the rotor should be replaced.
Check up blades on absence of damages.
|
Fig. 3.143. Check статора (1) on chain breakage
|
Check up статор on breakage of a chain 1 ( fig. 3.143), using an ohmmeter. The ohmmeter indication should be low enough, or статор should be replaced.
|
Fig. 3.144. Check статора on breakage of a chain or short circuit (1)
|
Check up статор on breakage of a chain or short circuit 1 ( fig. 3.144), using an ohmmeter. The ohmmeter indication should be high enough, or статор should be replaced.
Check up диодный the bridge in a following order:
|
Fig. 3.145. Conductivity check диодного the bridge in a direct direction (1)
|
- Check up conductivity диодного the bridge in a direct direction. Check up lead plugs of the coil статора on chain breakage, using an ohmmeter 1 ( fig. 3.145);
|
Fig. 3.146. Conductivity check диодного the bridge in the opposite direction (1)
|
- Check up conductivity диодного the bridge in the opposite direction. Check up lead plugs of the coil статора on chain breakage, using an ohmmeter 1 ( fig. 3.146);
- Replace диодный the bridge if it is necessary.
|
Fig. 3.147. A place of measurement of length of brushes ()
|
Check up deterioration of brushes. If length of brushes less than maximum permissible size and = 14 mm ( fig. 3.147), replace brushes.
Assemblage
Generator assemblage spend to sequences, return to removal.
Tighten the screw of fastening of a regulator of pressure the moment 9—12 Нм.
Tighten the fastening screw диодного the bridge/regulator of pressure the moment 9—12 Нм.
Tighten the screw of fastening of a shchetkoderzhatelja/regulator of pressure the moment 9—12 Нм.
Tighten fastening bolts диодного the bridge the moment 9—12 Нм.
Tighten a nut of fastening of a pulley the moment 80—110 Нм.
Tighten coupling bolts the moment 4—6 Нм.
Tighten a nut of fastening of the positive plug of the storage battery the moment 4—7 Нм.
|