Daewoo Matiz since 1997 of release
1. The general data
2. Maintenance service
3. The engine
3.1. A mechanical part of the engine
3.2. Cooling system
3.3. An electric equipment
3.3.1. The design description
3.3.2. A starter
3.3.3. Possible malfunctions of an electric part of the engine and methods of their elimination
3.3.4. The generator
3.3.5. The storage battery
3.3.6. The ignition distributor
3.3.7. The ignition coil
3.3.8. Starter check
3.3.9. Repair and check of the generator of type And (MANDO)
3.3.10. Repair and check of the generator of type In (DAC)
3.3.11. Repair of the distributor of ignition
3.4. A control system of the engine
3.5. System of release of the fulfilled gases
4. Transmission
5. A running gear
6. A steering
7. Brake system
8. Systems of heating, ventilation and air-conditioning
9. A body electric equipment
10. A body
11. Schemes электроборудования
 









3-3-9-remont-i-proverka-generatora-tipa-a-mando.html

3.3.9. Repair and check of the generator of type And (MANDO)

Dismantling

Fig. 3.116. The generator of type And (MANDO): 1 — the generator in gathering; 2 — a tension arm; 3 — a nut; 4 — a generator pulley; 5 — the plug (big); 6 — a generator cover; 7 — the forward bearing; 8 — a fixing payment; 9 — the plug (small); 10 — a generator anchor; 11 — the back bearing; 12 — статор the generator; 13 — диодный the bridge; 14 — a regulator of pressure / of a brush; 15 — the generator case; 16 — a nut of fastening of the "positive" plug of the storage battery; 17 — a coupling bolt




Details of the generator of type And (MANDO) are shown in drawing 3.116.
Remove the generator.

Fig. 3.117. An arrangement of coupling bolts (1) generators




Turn out coupling bolts 1 (fig. 3.117) the generator.

Fig. 3.118. Use of screw-drivers for branch of a cover from the generator




Using screw-drivers as levers, separate a cover from the generator case (fig. 3.118).
Remove a pulley and a rotor in gathering from a generator cover in a following order:

Fig. 3.119. Removal of a pulley and a cover from a generator rotor: 1 — a fabric; 2 — a rotor; 3 — a nut; 4 — a pulley




- Wrap up a rotor a fabric 1 (fig. 3.119);
- Fix a rotor 2 in a vice, a pulley upwards;
- Turn away a nut of 3 fastenings of a pulley;
- Remove a pulley 4.
Uncover, a rotor and the plug in a following order:

Fig. 3.120. Removal from a rotor (2) big plugs (1), a cover and the small plug (3)




- Remove the big plug 1 (fig. 3.120);
- Remove a rotor 2 from a cover;
- Remove the small plug 3 from a rotor axis.
Remove the forward bearing in a following order:

Fig. 3.121. An arrangement of screws (1) fastenings of a plate and the forward bearing of the generator




- Turn away screws 1 (fig. 3.121) a fixing payment;
- Remove a fixing payment 2;
- Using a press, remove the forward bearing 3 generators.
Turn away a nut of fastening of the "positive" plug to the generator and remove a washer.
Remove статор from the generator case in a following order:

Fig. 3.122. An arrangement of screws of fastening диодного the bridge (1), щеткодержателя both a regulator of pressure (2) and removal статора (3) with диодным the bridge/shchetkoderzhatelem/regulator of pressure (4)




- Turn away fastening screws диодного the bridge 1 (fig. 3.122);
- Turn away screws of fastenings щеткодержателя and a regulator of pressure 2;
- Remove статор with диодным the bridge/shchetkoderzhatelem/regulator of pressure 3.
Отпаяйте wires also remove диодный the bridge and a winding статора.
Check

Fig. 3.123. Check of breakage of a chain of a rotor (1)




Ohmmeter check up a rotor 1 (fig. 3.123) on chain breakage. Replace a rotor if it is necessary.

Fig. 3.124. Check of a winding of a rotor on breakage (1) and short circuit on "weight" (2)




Check up a rotor winding on breakage 1 (fig. 3.124) or chain short circuit. Resistance of a winding of a rotor 2,9 Ohm. Replace a rotor if it is necessary.
Check up a rotor on breakage of a chain or short circuit on "weight", using an ohmmeter. Replace a rotor if it is necessary.

Fig. 3.125. Check статора on breakage of a chain (1)




Check up статор on chain breakage, using an ohmmeter 1 (fig. 3.125). Replace статор if it is necessary.

Fig. 3.126. Check статора on breakage of a chain or short circuit on "weight" (1)




Check up статор on breakage of a chain or short circuit on "weight" 1 (fig. 3.126), using an ohmmeter.
Check up диодный the bridge in a following order:

Fig. 3.127. Conductivity check диодного the bridge in a direct direction (1)




- Check up conductivity диодного the bridge in a direct direction. Check up lead plugs of the coil статора on chain breakage, using an ohmmeter 1 (fig. 3.127);

Fig. 3.128. Conductivity check диодного the bridge in the opposite direction (1)

Fig. 3.129. Use of an ohmmeter for check of the threefold diode (1) and a heat-conducting path (2)




- Check up conductivity диодного the bridge in the opposite direction. Check up lead plugs of the coil статора on chain breakage, using an ohmmeter 1 (fig. 3.128);
- Replace диодный the bridge if it is necessary.
Check up diodes in a following order:

Fig. 3.129. Use of an ohmmeter for check of the threefold diode (1) and a heat-conducting path (2)




- Check up the threefold diode, using an ohmmeter 1 (fig. 3.129);
- Replace a heat-conducting path 2 if it is necessary.

Fig. 3.130. A place of measurement of length of brushes ()




Check up deterioration of brushes. If length of brushes less than maximum permissible size and = 13,5 mm (fig. 3.130), replace brushes.
Assemblage
Generator assemblage spend to sequences, return to removal.

Fig. 3.131. Fixing of brushes () in the pressed position by a wire piece b inserted into an aperture (1)




Before installation щеткодержателя on contact rings of a rotor, press brushes in щеткодержатель and fix them, having inserted into apertures 1 (fig. 3.131) a wire piece.
Tighten screws of a shchetkoderzhatelja/regulator/diodnogo of the bridge the moment 9—12 Нм.
Tighten screws of a fixing payment of the forward bearing the moment 6—8 Нм.
Tighten a nut of fastening of a pulley of the generator the moment 80—110 Нм.
Tighten coupling bolts b the moment 4—6 Нм.






To return back
3.3.8. Starter check
On the following page
3.3.10. Repair and check of the generator of type In (DAC)